HYDRAULIC LIFTS

If you are looking for a hydraulic lift for your boat then SeaLift has the perfect, Patented design that uses a Single Point of Power utilizing one cylinder and two hydraulic lines outboard of the transom.
 
While other hydraulic lifts on the market use four cylinders in their design, SeaLift’s Patented design accomplishes a lot more with only one cylinder while greatly reducing the number of unnecessary parts exposed to water, significantly reducing annual maintenance and increasing service life.
 
Although SeaLift’s compact design uses fewer cylinders, it still has plenty of power! And depending on your boat’s capabilities, it can lift up to 2,500 pounds with the Single Point of Power.

Each SeaLift Platform Lift is individually engineered to guarantee a perfect fit for your boats specific year, Make and Model eliminating the need for shims, adapter brackets, or expensive fiberglass modifications to your boat’s hull.
 
Since the SeaLift Platform Lift is custom built for your boat, installation is straight forward allowing marine technicians at marina service facilities to install the SeaLift in a couple of days.

 PLATFORM LIFTS

SeaLift has a Patented (US Patent # 7707955B1) design on our proprietary Lift Mechanism. While hydraulic lifts on the market use four cylinders in their designs. SeaLift use a Single Point of Power utilizing one cylinder and two hydraulic lines outboard of the transom. This significantly reduces the routine maintenance required and greatly increases reliability by eliminating many unnecessary parts.  This design allows the SeaLift to be compact put powerful.
 
Although SeaLift’s design uses fewer cylinders, it still has plenty of power and, depending on your boat’s capabilities, can lift up to 2,500 pounds with the Single Point of Power system

Each SeaLift Platform Lift is individually engineered to guarantee a perfect fit for your boat’s specific year, Make and Model eliminating the need for shims, adapter brackets, or expensive fiberglass modifications to your boat’s hull.
 
Since the SeaLift Platform Lift is custom built for your boat, installation is straight forward allowing marine technicians at marina service facilities to install the SeaLift in a couple of days.

1/6

 FEATURES

SeaLift has a Patented (US Patent # 7707955B1) design on our proprietary Lift Mechanism. While other hydraulic lifts on the market use four cylinders in their designs. SeaLift uses a Single Point of Power utilizing one cylinder and two hydraulic lines outboard of the transom. This significantly reduces the routine maintenance required and greatly increases reliability by eliminating many unnecessary parts.  This design allows the SeaLift to be compact but powerful.

By utilizing a Single Point of Power, the SeaLift system eliminates the “Racking” experienced by other systems.  Additionally, this allows the transom mount to be customized to fit in the middle of the transom with strength support of the inner stringers and eliminates multiple hydraulic lines, fittings, flow dividers, thru hulls, and uneven lifting!  Lifting capacity can be engineered to over 2,500 lbs.
Patented Over Center lock design eliminates the need for additional locking cylinders and hydraulic phasing which is prone to failure.  The SeaLift system eliminates complexity and depends on 100% reliable geometry.

Extended Cross Support transfers load uniformly.  Additionally, The SeaLift system allows for the option of an intermediate step.

Jacking Plates allow for both vertical and horizontal adjustment of the platform during installation and throughout the life of the lift without the need to remove the platform.

Adjustable Control Rods allow for infinite attitude adjustment of the swim platform and can even be adjusted with the boat in the water!

Patented self-adjusting Pop Up Chocks.

Specially designed Compression Pads integrated into the platform support contact the extended cross tube of the Mainframe allowing adjustment to eliminate vibration and assure cross stability.

State of the art Hydraulic Power Unit with solid state electronic control, Ignition Protected motor, 12 or 24 VDC, Remote Controls, Back Up Corded Controller, System Articulation Warning sound, Pressure meter, and backup Hand Pump.

Stainless Steel construction with 954 Navel Bronze bushings.  SeaLift unit is also coated with Anti-Fouling paint so it’s launch ready when installed.

 

 THE SEALIFT PLATFORM ALSO INCLUDES

  • Stainless Steel Construction with 954 Navel Bronze bushings

  • Custom Engineered Hydraulic Lift Mechanism

  • Custom Designed Swim Platform

  • SeaLift’s Exclusive Pop-Up Chocks

  • Swim Ladder

  • 4 Stainless Steel Tie Down Straps

  • Folding Pad-Eyes

  • Hydraulic Power Unit (HPU)

  • Control harness Wiring

  • Wireless Remote Control Key Fobs (2)

  • Corded Controller

  • All Hardware Required for Installation

  • Anti-fouling Bottom Paint

  • One Year Warranty

1/6

 ENGINEERING

Every SeaLift design is custom engineered to fit the transom of the individual boat. If you are interested in purchasing a SeaLift customized specifically to your boat and your needs,  contact us with your boat’s Year, Make, Model, and any factory or aftermarket options. We will then be able to select the design and customize it to be an exact fit for your boat and individual needs.

SeaLift offers a variety of designs that we have engineered to accommodate a variety of features commonly encountered on boats, such as transom shape, stern drives, and integrated swim platforms.

 ONE CYLINDER PLATFORM LIFT

Sometimes less is more and this is especially true when it comes to SeaLift’s Single Cylinder Platform Lift. SeaLift’s Patented design of the lift mechanism uses only a single cylinder acting on a Single Point of Power instead of the traditional four cylinders. SeaLift Platform Lifts, designed for boats 35′-70′ uses only one cylinder and two hydraulic lines outboard of the transom.

Since the Platform Lift only uses one cylinder there are no unnecessary parts exposed to the water, which reduces the routine maintenance that is usually required.

Although the SeaLift’s Platform Lift is compact and uses fewer cylinders, it is still plenty powerful. Depending on your boat’s capabilities, the Single Cylinder Platform Lift can lift up to 1,000 lbs.

 DUAL CYLINDER PLATFORM LIFT

In some transom configurations it is necessary to use a dual cylinder system which still incorporates the over center lock.. With two cylinders, this Platform Lift will allow your yacht to carry a larger tender as well as a larger swim platform. With the Dual Cylinder Platform lift you can carry up to 2,500 lbs!

The options and features of our Single Point of Power system are also available including custom designed swim platform, Pop-Up Chocks, and finish options such as teak decking.

 SeaLift Platform Lifts are available as a factory option from these fine boat manufacturers

Please join our mailing list

3309 N Courtenay Pkwy STE A
Merritt Island FL 32953-8341

PHONE -321-638-0301

 FAX- 321-638-0309